New to Planet Derby Bentley
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
New to Planet Derby Bentley
I have recently migrated from WO to a Derby Bentley with Park Ward Saloon body. One or two questions from a new (older) boy.................
Has anyone done anything innovative but reversible with the fag lighter and ash tray? I do not use them and though correct are not needed.
Has anyone fitted a battery isolation switch? Having some experience of electrical faults that become fires I have generally fitted them to any cars that I have had. Is it needed and where might a switch be located so that it is easily accessible from inside the car? I am slightly perplexed at the number of things that are on (live) when the ignition is off!
There is a rear screen blind that should go up and down is there any knowledge around on how this works? There is a thread through the roof lining.
What are the recommended spark plugs please ?
Anyone any advice on fitting an electronic cut out to replace the regulator and wound resistor ?
Thanks
I am sure more questions will emerge as time goes by
Has anyone done anything innovative but reversible with the fag lighter and ash tray? I do not use them and though correct are not needed.
Has anyone fitted a battery isolation switch? Having some experience of electrical faults that become fires I have generally fitted them to any cars that I have had. Is it needed and where might a switch be located so that it is easily accessible from inside the car? I am slightly perplexed at the number of things that are on (live) when the ignition is off!
There is a rear screen blind that should go up and down is there any knowledge around on how this works? There is a thread through the roof lining.
What are the recommended spark plugs please ?
Anyone any advice on fitting an electronic cut out to replace the regulator and wound resistor ?
Thanks
I am sure more questions will emerge as time goes by
Last edited by Steve Welton on Sat Jun 11, 2016 8:03 am, edited 1 time in total.
-
Christopher Carnley
- Posts: 2753
- Joined: Fri Nov 16, 2007 12:00 am
- Location: Yorkshire, United Kingdom
Steve,
A good start would be to buy the "Green Book", or The Derby Bentley Technical Manual.
What is the chassis number of your car and is the cylinder head the original cast iron one or a later aluminium alloy replacement?
The best way to eliminate a lot of ignition problems is to fit a modern 12 volt coil, either as a direct replacement, or situated on the side valance with the low tension lead by-passing the antiquated ballast resistor.
You could fit an isolator between the battery and the main starter switch (solenoid) on the left of the bulkhead, but check first if there are any other connections onto the battery itself.
(Although I hesitate to say it (not), you will wish that you had bought a good running R Type synchromesh car.)
Buy all your parts from Will Fiennes, (say no more).
A good start would be to buy the "Green Book", or The Derby Bentley Technical Manual.
What is the chassis number of your car and is the cylinder head the original cast iron one or a later aluminium alloy replacement?
The best way to eliminate a lot of ignition problems is to fit a modern 12 volt coil, either as a direct replacement, or situated on the side valance with the low tension lead by-passing the antiquated ballast resistor.
You could fit an isolator between the battery and the main starter switch (solenoid) on the left of the bulkhead, but check first if there are any other connections onto the battery itself.
(Although I hesitate to say it (not), you will wish that you had bought a good running R Type synchromesh car.)
Buy all your parts from Will Fiennes, (say no more).
-
Christopher Carnley
- Posts: 2753
- Joined: Fri Nov 16, 2007 12:00 am
- Location: Yorkshire, United Kingdom
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
- John Murch
- Posts: 1586
- Joined: Sat Jun 05, 1976 11:00 pm
- Location: London, United Kingdom
- Stephen Blakey
- Posts: 1348
- Joined: Thu Feb 02, 1995 12:00 am
- Location: Derbyshire, United Kingdom
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
-
John Robins
- Posts: 1208
- Joined: Tue Jan 01, 1985 12:00 am
- Location: Staffordshire, United Kingdom
It would not be legal to use an exhaust cut out on the road, and for occasional track use you would have to find some way of diverting the hot gases away from the body and oil or fuel lines (and wiring!). It may also upset the mixture to remove the exhaust back pressure and my personal view would be that for general purpose road use you don't need one.
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
- Stephen Blakey
- Posts: 1348
- Joined: Thu Feb 02, 1995 12:00 am
- Location: Derbyshire, United Kingdom
They were a popular go-faster addition in the early days. With no computers to help design the silencers, the price of silence was a drop in engine performance. I haven't seen one on a post-war car so maybe the Derbys were the last to have such things?
From a 21st C perspective these do seem like breathtakingly antisocial devices. Did people really use them on the road? You wouldn't be allowed to use one on a track nowadays as the noise limits are quite conservative.
It would be a shame if they disappeared altogether as these things are a part of the history of our cars. Hopefully you will at least keep the bits of the system you've got?
From a 21st C perspective these do seem like breathtakingly antisocial devices. Did people really use them on the road? You wouldn't be allowed to use one on a track nowadays as the noise limits are quite conservative.
It would be a shame if they disappeared altogether as these things are a part of the history of our cars. Hopefully you will at least keep the bits of the system you've got?
-
Ewan Gallie
- Posts: 184
- Joined: Wed Oct 29, 1997 12:00 am
- Location: Italy
I see Fiennes have them for sale (at a price) but they refused to fit one for me because of them not being road legal. I believe there are corrosion problems too. I have the lever still there but it’s not connected. There is someone I know in Italy who fitted one to his recently restored 3 ½ and he says it works well, you do sacrifice the silent part of the sports car! I was told that it should be used only to give you the extra horse when doing a fast pass-out on the highway and make a rude noise at the same time!John Robins wrote:It would not be legal to use an exhaust cut out on the road, and for occasional track use you would have to find some way of diverting the hot gases away from the body and oil or fuel lines (and wiring!). It may also upset the mixture to remove the exhaust back pressure and my personal view would be that for general purpose road use you don't need one.
Ciao,
Ewan
-
Charles R Simmers
- Posts: 117
- Joined: Wed Apr 19, 2000 11:00 pm
- Location: Arizona, USA
These are readily available here in the States. Here is one, for instance.
http://www.jegs.com/p/JEGS-Performance- ... 9/10002/-1
Police citations are also readily available.
http://www.jegs.com/p/JEGS-Performance- ... 9/10002/-1
Police citations are also readily available.
-
Christopher Carnley
- Posts: 2753
- Joined: Fri Nov 16, 2007 12:00 am
- Location: Yorkshire, United Kingdom
I pull them out levers and all, they were banned in the 4 1/4 cars, far too noisy and with the CO leaks, lethal!
After 6 months to the day, I got the 3 1/2 litre machined engine parts back last Friday, so it is all go now to get it back to Windsor.
Fairly (B) fiddly as always, until I came to the new, Fiennes, high compression pistons, the gudgeon pin hole instead of being .0001" fit ,hot, was in fact a .010" fit, and I had to obtain a special reamer to scrape out the holes.
So before anybody starts brainstorming, I should have been waiting weeks for them if I had set them back.
Pics to follow if I can remember to take any.
After 6 months to the day, I got the 3 1/2 litre machined engine parts back last Friday, so it is all go now to get it back to Windsor.
Fairly (B) fiddly as always, until I came to the new, Fiennes, high compression pistons, the gudgeon pin hole instead of being .0001" fit ,hot, was in fact a .010" fit, and I had to obtain a special reamer to scrape out the holes.
So before anybody starts brainstorming, I should have been waiting weeks for them if I had set them back.
Pics to follow if I can remember to take any.
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
-
John Robins
- Posts: 1208
- Joined: Tue Jan 01, 1985 12:00 am
- Location: Staffordshire, United Kingdom
The nearest I can get is Autocar road test #1030, no date shown in my book, 4 1/4 with what is described as standard saloon body, and looks like a PW 4 light.
Weight without passengers 33cwt 1qr 22lb.
A later test Nov 12th 1937, #1149 says 34cwt 1qr 20lb.
Test #1269 April 7th 1939, says 35cwt 0qr 23lb.
Capt. McLeod's "H1" weighed in at 31cwt.
http://www.rrab.com/mcleod.htm
On 28th May 1937 G. Geoffrey Smith wrote an article called "3 1/2 and 4 1/4 litres compared" and quotes 33cwt and 35cwt respectively, and moans that the later car gets through tyres more quickly, recommending the Pneugrippa retread process (!).
Weight without passengers 33cwt 1qr 22lb.
A later test Nov 12th 1937, #1149 says 34cwt 1qr 20lb.
Test #1269 April 7th 1939, says 35cwt 0qr 23lb.
Capt. McLeod's "H1" weighed in at 31cwt.
http://www.rrab.com/mcleod.htm
On 28th May 1937 G. Geoffrey Smith wrote an article called "3 1/2 and 4 1/4 litres compared" and quotes 33cwt and 35cwt respectively, and moans that the later car gets through tyres more quickly, recommending the Pneugrippa retread process (!).
Last edited by John Robins on Fri Jul 15, 2016 10:28 am, edited 3 times in total.
-
Christopher Carnley
- Posts: 2753
- Joined: Fri Nov 16, 2007 12:00 am
- Location: Yorkshire, United Kingdom
The weight of the 3 1/2 litre chassis is 2510 lbs. "The Company" ie Rolls -Royce set a weight limit for the bodywork of 8 1/2 cwt and only P W were able to manage this.
McLeod's shorty, B142 MR was an H J Mulliner aberration and originally fitted to his B171LE, he continued this trend right up to the post war S3 Continentals.
McLeod's shorty, B142 MR was an H J Mulliner aberration and originally fitted to his B171LE, he continued this trend right up to the post war S3 Continentals.
- John Murch
- Posts: 1586
- Joined: Sat Jun 05, 1976 11:00 pm
- Location: London, United Kingdom
-
Christopher Carnley
- Posts: 2753
- Joined: Fri Nov 16, 2007 12:00 am
- Location: Yorkshire, United Kingdom
-
Steve Welton
- Posts: 105
- Joined: Thu Oct 17, 2013 5:37 pm
Many thanks for such a prompt response.
I will see if I can get "Brooklands Books 'Bentley Cars 1934 - 1939'
In the meantime I would greatly appreciate a scan of the 34 PW Saloon test please John.
The reason for needing to know is I am contemplating buying a car lift arrangement see here http://www.carlift-ramp-mr1.com/ As I get older I need to find ways of making maintenance tasks a little easier, this seemed an improvement on ramps and jacks.
I will see if I can get "Brooklands Books 'Bentley Cars 1934 - 1939'
In the meantime I would greatly appreciate a scan of the 34 PW Saloon test please John.
The reason for needing to know is I am contemplating buying a car lift arrangement see here http://www.carlift-ramp-mr1.com/ As I get older I need to find ways of making maintenance tasks a little easier, this seemed an improvement on ramps and jacks.
-
John Robins
- Posts: 1208
- Joined: Tue Jan 01, 1985 12:00 am
- Location: Staffordshire, United Kingdom



