Weight of 3ltr Radiator

Forum specifically for WO Bentley car issues.
(Public visibility)
Post Reply
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Weight of 3ltr Radiator

Post by John Murch »

Would anyone happen to know the weight of a dry 3ltr radiator?

I don’t want to surprise myself when I take it off!
Christopher Carnley
Posts: 2753
Joined: Fri Nov 16, 2007 12:00 am
Location: Yorkshire, United Kingdom

Post by Christopher Carnley »

260 lb.
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Post by John Murch »

Thank you Christopher, much appreciated, I will not try lifting that off the car single handed!
User avatar
Stephen Blakey
Posts: 1348
Joined: Thu Feb 02, 1995 12:00 am
Location: Derbyshire, United Kingdom

Post by Stephen Blakey »

FWIW, having reached the ripe old age of 67, I've started using an engine crane to remove radiators. Maybe my back would be in better shape if I'd started a bit sooner? Anyway, good luck.
Stephen
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Post by John Murch »

I have just invested in a 7 ratio block and tackle. Sadly I won’t be doing the job soon as the Thames has just flooded and my car (though dry) is now inaccessible.
Iain Warner
Posts: 148
Joined: Fri Apr 03, 1992 11:00 pm
Location: Norfolk, United Kingdom

Post by Iain Warner »

I have so far always managed to remove mine singlehanded without using any lifting appliance. Headlights and support pillars removed first and water pump lifted off with radiator. Lesson I found was to know exactly where I was going to put it down close by once removed.
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Post by John Murch »

Iain, I hadn’t contemplated taking the water pump off with the radiator, do you do that due to difficulty in removing and reattaching the bottom hose, or for some other reason?
Iain Warner
Posts: 148
Joined: Fri Apr 03, 1992 11:00 pm
Location: Norfolk, United Kingdom

Post by Iain Warner »

John, It just seemed the easy thing to do. I hinge the disconnected radiator forward on the trunnions at the same time easing the pump from the housing and lifting off together with pump held on by bottom hose.
My rad of course is wider at the top but then does not have the later type header tank extending back. Also I suppose the weight will vary with how scaled up the core is.
DavidThompson
Posts: 139
Joined: Thu Sep 10, 2015 11:00 pm
Location: Hampshire, United Kingdom

Post by DavidThompson »

I cut the hoses off before removing my radiator, as I intended replacing with new ones.
Without doubt putting it back on with the water pump attached made the job much easier.
You may find the inlet tube to the pump is corroded away, and if so an effective repair can be carried out using 26mm aluminium sleeve inside and 32mm tube bonded with JB Weld.
Let me know if you need some - I had to buy 2 metres to get the 2 inches I needed.
DavidSimpson5769
Posts: 9
Joined: Fri Mar 08, 2019 12:00 am
Location: Kent, United Kingdom

Post by DavidSimpson5769 »

I realise this is a very late response to this post but I have just weighed my 3 litre rad' an early one with no header tank fitted, it weighs 22 kilos, approximately 50 lbs.
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Post by John Murch »

Thanks David, 22kg that is much more manageable, I didn’t think I could manage 100kg by myself but 22kg is much more reasonable. My rad may be a bit heavier as although one of the lower ones, it was fitted with a header tank when last recored.
Post Reply