R Type Piston Rings (std)

Forum for Crewe Cars through S-Type & Derivatives
(Public visibility)
Post Reply
Al Coutts
Posts: 108
Joined: Sun Sep 25, 2016 11:00 pm
Location: Norfolk, United Kingdom

R Type Piston Rings (std)

Post by Al Coutts »

Hi - none of the usual suspects have any standard rings available.

Does anyone have any leads?

Does snyone know the bore, depth of the rings and ring thicknesses?

All suggestions gratefully received!

Thanks,


Al
Christopher Carnley
Posts: 2753
Joined: Fri Nov 16, 2007 12:00 am
Location: Yorkshire, United Kingdom

Post by Christopher Carnley »

Did you contact F W Thornton in Shrewsbury?
User avatar
John Murch
Posts: 1586
Joined: Sat Jun 05, 1976 11:00 pm
Location: London, United Kingdom

Post by John Murch »

http://rrtechnical.info/mkvi/wshoplate/2.pdf

Scroll down to page 7, is this what you need?
User avatar
Stephen Blakey
Posts: 1348
Joined: Thu Feb 02, 1995 12:00 am
Location: Derbyshire, United Kingdom

Post by Stephen Blakey »

To answer your question, the bore is 3 5/8" which is 92.075mm. Don't know the ring thickness but could measure a few this evening if that would help.
Hopefully you can find a set of the shelf. Was there a 3 5/8" military engine? I've a feeling they have jumped straight to 3 3/4?
As a bit of a last resort, DLA engines of, ahem, Athens, sell piston rings by the mm. You could spend a lot of time navigating through their thousands of listings and may then end up have to machine out the grooves. On the plus side this would freshen them up and restore the clearance. Christopher put me on to these people.

https://www.ebay.co.uk/itm/Piston-Rings ... _V9BYUQs1Q

John, It's interesting that on the page you refer to, someone has written on the shell bearing OD's. I wonder if said person was hoping to find a set of shells from another engine to avoid spending a zillion pounds on a set individually hand-made by Belgian nuns?
Christopher Carnley
Posts: 2753
Joined: Fri Nov 16, 2007 12:00 am
Location: Yorkshire, United Kingdom

Post by Christopher Carnley »

All those "Greek" piston rings are made made in Turin.

Your piston ring grooves will be worn and bell mouthed.
Christopher Carnley
Posts: 2753
Joined: Fri Nov 16, 2007 12:00 am
Location: Yorkshire, United Kingdom

Post by Christopher Carnley »

All those "Greek" piston rings are made made in Turin.

Your piston ring grooves will be worn and bell mouthed.
Al Coutts
Posts: 108
Joined: Sun Sep 25, 2016 11:00 pm
Location: Norfolk, United Kingdom

Post by Al Coutts »

Thank you all, again!

I've had a discussion with Thorntons - they are based very close to my parents and they can't help.

When I add it all up, a set of replacement pistons c/w rings and gudgeon pins from T&G, is not a million miles from re-grooving the existing pistons and cobbling together a set from various suppliers.

I did find the same piston/ring/pin set in the US for a LOT less and do have a house-guest next month from Boston, Ma. Unfortunately, he's travelling mil-air and despite his exalted rank will not be able to bring them over!
Norman Geeson
Posts: 2
Joined: Tue Mar 20, 2012 4:29 pm

Post by Norman Geeson »

You should find a number of the different 4.2 ltr. Jaguar rings will do the job.
Al Coutts
Posts: 108
Joined: Sun Sep 25, 2016 11:00 pm
Location: Norfolk, United Kingdom

Post by Al Coutts »

Thank you Norman - decision not yet made, so will look into that.

Love your website, by the way - it's inspired me to take on an R Type rebuild!
Post Reply